Volkswagen Polo Service & Repair Manual: Tires and Rims, Matching
			
			
			
	
		| 
			
				| If necessary repair flat spots from standing. Refer to
				→ Chapter „Flat Spots, Correcting“. |  
			
				| – | Dismount the tire. Refer to 
				→ Chapter „Tires, Dismounting“. |  
			
				| – | Turn the tire about 180° against the rim. |  
			
				| – | Inflate the tire to 4 bar (58 psi). |  
			
				| – | Tension the wheel with the tire on the balancing machine. |  
			
				| – | Check the tire and wheel radial and lateral run-out. Refer 
				to 
				→ Chapter „Wheel, Balancing, Tire and Wheel Radial and Lateral 
				Run-Out, Checking“. |  
			
				| – | If the radial and lateral run-out are within the specified 
				values, balance the wheel to 0. Refer to 
				→ Anchor. |  
			
				| – | If the radial and lateral run-out are outside the specified 
				values, match the tire and rim again and rotate the tire 90° 
				relative to the rim. |  
			
				| – | Check the tire and wheel radial and lateral run-out again. 
				Refer to 
				→ Chapter „Wheel, Balancing, Tire and Wheel Radial and Lateral 
				Run-Out, Checking“. |  
			
				| – | If the radial and lateral run-out are within the specified 
				values, balance the wheel to 0. Refer to 
				→ Anchor. |  
			
				| – | If the radial and lateral run-out are outside the specified 
				values, match the tire and rim again and rotate the tire 180° 
				relative to the rim. |  
			
				| – | Check the tire and wheel radial and lateral run-out again. 
				Refer to 
				→ Chapter „Wheel, Balancing, Tire and Wheel Radial and Lateral 
				Run-Out, Checking“. |  
			
				| – | If the radial and lateral run-out are within the specified 
				values, balance the wheel to 0. Refer to 
				→ Anchor. |  
			
				| – | If the radial and lateral run-out are still outside the 
				specified values check the rim for radial and lateral run-out. 
				Refer to 
				→ Chapter „Wheel Balancing, Rim Radial and Lateral Run-Out, 
				Checking“. |  
			
				| – | In the radial and lateral run-out of the rim is within the 
				specified values, replace the tire. |  |  |  | 
   
	
		
		
			
				Only trained personnel can perform the assembly work on 
				run-flat tires and ultra high performance tires.
			
		
		
			
				
				If equipped check the tire pressure mo ...
   
 
   Other materials:
Paint System for Plastic Parts
   
	
		
		
			
				This universal painting system enables you to safely and 
				simply paint all plastic parts which can be usually found on the 
				exterior. (Plastic types: PP, EPDM, ABS, PC, PPO, PBTP, UP-GF, 
				PA, PVC, R-TPU, PUR) This technical reference material does not 
				apply ...
   
Checklist
   
	To ensure your own safety and that of your passengers, observe 
	the following actions in the specified order :
	Stop the vehicle at a safe distance 
	away from moving traffic and on a suitable surface . 
	
	Switch on the hazard warning lights 
	using the button . 
	
	Apply the handbrake  ...
   
Vehicle lifting points
   Fig. 150 Lifting points at front for the 
lifting platform or vehicle jack 
Fig. 151 Lifting points at rear for the 
lifting platform or vehicle jack 
First read and observe the introductory information 
and safety warningsThe vehicle may only be lifted at the points shown in 
the illustration ...
   
 
	 
	
	
		
			© 2016-2025 Copyright www.vwpolo.net
