Volkswagen Polo Service & Repair Manual: Two-Part Fine Filling Paste
| Two-Part Fine Filling Paste -LSP 784 002 A2- |
| The two-part fine filling paste is a very fine thixotropic
polyester filling paste. |
| This filling paste is suitable for small repairs. |
| High elasticity for touching up synthetic surfaces |
| Glass fiber reinforced plastics |
| Old paint and factory paint |
| Hardened two-part filler/two-part primers |
| Plastic parts glaze-primed with Two-Part Plastic Adhesive
Filler -LKF 696 009 A2-/-LKF 696 040 A2- or Adhesion Promoter -ALO
822 000 10- |
| Primed surfaces with two-part polyester filling paste. |
Caution
| This filling paste may not be applied to PVB
(acid-hardening) adhesive primers or one-part primers
(for example, synthetic resin). |
| Application on thermoplastic or elastic coatings is
also not possible. In these cases, only apply filler
paste to bare steel. |
|
|
|
|
| Pre-treatment of base surfaces: |
| – |
Remove any grease and sand the surface. |
| – |
Bare metallic base surfaces are to be insulated with
Two-Part Wash Primer -LHV 043 000 A2- and then filled with
Two-Part HS Performance Filler. Sand the filler after drying. |
| – |
With UP-GF underbodies, clean components of any residual
agents and sand the surface. |
|
|
|
| – |
Use a suitable cleaning agent before reworking to ensure a
clean and residue-free surface. |
|
|
|
| – |
Add 2 to 3 % by weight Two-Part Hardener -LVM 018 000 A1/A2-
or, especially when dealing with high temperatures, Two-Part
Hardener, Long -LVM 018 100 A2-. |
 Note
| Avoid using excessive hardener paste, to prevent it from
bleeding through, especially on daylight colors and light
metallic colors. |
| – |
At +20 °C (68 °F) room temperature for about three to five
minutes. |
|
|
|
| – |
At +20 °C (68 °F) room temperature for about 20 to 30
minutes. |
|
|
|
| Short-wave heaters for three minutes (at 50 % power) |
| Medium-wave heaters for five minutes. |
|
|
|
| In connection with the aforementioned drying time: |
| – |
Dry-sand the pre-sanding with P180-240 grit sandpaper |
| – |
Dry-sand the final sanding with P240-320 grit sandpaper |
|
|
|
| – |
While wet, sand the pre-sanding with P240-320 sandpaper |
| – |
While wet, sand the final sanding with P600-800 sandpaper |
Note
| When wet-sanding, make sure to wipe and dry off the surface. |
| Temperature resistance up to +80 °C (176 °F). |
|
|
|
| One-Part Wash Primer -LVM 044 007 A2-/-LVM 044 171 A2- |
| Two-Part Wash Primer -LHV 043 000 A2- and Two-Part HS Vario
Filler |
| Two-Part Plastic Adhesive Filler -LKF 696 009 A2-/-LKF 696
040 A2- |
| Unelasticized Adhesion Promoter -ALO 822 000 10- and
Two-Part HS Filler (for plastic parts) |
| – |
Then paint over with the top coat. |
|
|
|
| Personal Protective Equipment: |
| Note the safety data sheets |
| Wear the personal protective equipment during application |
|
|
|
| Delivery Viscosity |
pasty |
| Flashpoint: |
Filling paste over 23 °C (73.4
°F) |
| VOC value: 2004/42/IIB(b)(250)170 |
The EU limit for this product
(product category IIB.b) in ready-to-use form is a maximum of 250 g/L
volatile organic compounds. The VOC-value of this product in
ready-to-use form is a maximum of 170 g/L. |
| The guaranteed shelf life is 12 months from the production
date. Use no later than the date indicated on the label and
store in original container at +20 °C (68 °F). |
|
|
|
| – |
Storage Temperature +20 °C (68 °F) (temperature should not
exceed +30 °C (86 °F)). |
|
|
|
Definition:
Two-Part Steel Filling Paste Set -DA 787 300 A2-
Edition 09/2012
Product Description
...
Definition:
Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1-
Edition 07/2010
Product Description
The T ...
Other materials:
Midtronics Battery Tester -MCR340VKT-, Troubleshooting
Sometimes the display shows the malfunction or the messages
based on the condition.
The following is a list of the most frequent displayed
messages together with suggested solutions.
Note
Refer to the MCR3 ...
EU Tire Label, Goals
To reduce fuel usage
To improve road safety
To reduce traffic noise
The EU Tire Label Provides the End-User with Information
About the Tire's Most Important Properties. However, it Does ...
Wear Spots
A wear spot is a flat spot on the tread of the tires that
can be caused by extreme braking maneuvers on subsurface such as
asphalt.
At the same time a tire during the braking maneuver is
rubbed at selective points which ...
© 2016-2024 Copyright www.vwpolo.net
Two-Part Steel Filling Paste Set
Two-Part Fine Filling Paste, Flexible