Volkswagen Polo Service & Repair Manual: Two-Part Thinner

Volkswagen Polo Service & Repair Manual / General Paint Information / Original Products / Thinners / Two-Part Thinner

Definition:

Two-Part Thinner -LVE 009 001 A5-

Two-Part Thinner, Long -LVM 009 300 A2-

Two-Part Thinner, Plus -LHA 014 000 A5-

Two-Part Thinner, Special -LVM 009 200 A2-/-LVM 009 200 A5-

Nitrocellulose Thinner -LVE 856 000 A3-

Edition 04/2013

Product Description

The following section describes the VW thinners that are optimally suited to vehicle paint repairs.

These thinners can be used to alter the viscosity of the base products to achieve the best application under all conditions.

Note

They may not be used for thinning water-based base paints.

Application Instructions

Area of Application

Mixture ratio:

–	Refer to the technical application instructions for the respective base components

Thinner Selection

+ + -

Optimum

+ -

Suitable

- -	Partially suitable

- - -

Not suitable

Note

This table gives a general overview of the options for using the thinners listed here. Any additional information in the technical application information for the respective base component should take precedence.

Two-Part Thinner

Two-Part Thinner	Two-Part Thinner -LVE 009 001 A5-	Two-Part Thinner, Long -LVM 009 300 A2-	Two-Part Thinner, Plus -LHA 014 000 A5-	Two-Part Thinner, Special -LVM 009 200 A2-/-LVM 009 200 A5-
Two-Part HS Top Coat	+	++*	+	+ +
Two-Part HS Clear Coat**	- -	- -	- -	+ +
Two-Part Acrylic Primer/Filler	+ +	+*	+ +	+ +
Wash Primer	+ +	-*	+ +	+ +
* only for temperatures above +25 °C (77 °F)
** Two-part HS clear coat which is used in a 3:1 mixing ratio with two-part VHS hardeners plus thinner.

Main areas of application and thinner uses

Two-Part Thinner	Two-Part Thinner -LVE 009 001 A5-	Two-Part Thinner, Long -LVM 009 300 A2-	Two-Part Thinner, Plus -LHA 014 000 A5-	Two-Part Thinner, Special -LVM 009 200 A2-/-LVM 009 200 A5-	Nitrocellulose Thinner -LVE 856 000 A3-
Main area of application	Universally usable thinner for all two-part acrylic products	The specially designed thinner with viscosity-reducing properties is especially suitable for the two-part HS top coat, two-part acrylic filler.	Usable thinner for all two-part acrylic products with drying accelerator	A specially designed thinner with viscosity-reducing properties is especially suitable for the two-part HS top coat, two-part acrylic filler and two-part HS clear coat, which are used in a 3:1 ratio with two-part VHS hardeners plus thinner.	Equipment cleaner and degreaser
Use	For adjusting viscosity of base materials and top coats at low and moderate temperatures	For optimizing and improving the paint mist adhesion at spray booth temperatures above +25 °C (77 °F) and the presence of large surfaced objects at the same time.	For adjusting viscosity of base materials and top coats at low and moderate temperatures	For adjusting viscosity of base materials and top coats at low and moderate temperatures	The EU limit for this product (product category IIB.a) in its ready-to-use form is a maximum of 850 g/L volatile organic compounds. VOC value: 2004/42/IIB(a)(850)840
Characteristics	Flashpoint above +23 °C (73.4)	Flashpoint above +23 °C (73.4)	Flashpoint above +23 °C (73.4)	Flashpoint above +23 °C (73.4)	Flashpoint above +23 °C (73.4)

Personal Protective Equipment:

Note the safety data sheets

Wear the personal protective equipment during application

Two-Part Thinner

Storage

All thinners have a guaranteed shelf life of 60 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 °C (68 °F)

Two-Part Thinner

Thinners

...

HS Spot Thinner

Definition: HS Spot Thinner -LVM 006 000 A2- Edition 06/2013 Product Description ...

Other materials:

Adjusting the head restraints
Fig. 39 Adjusting front head restraint Fig. 40 Adjusting rear head restraint First read and observe the introductory information and safety warnings Every seat is fitted with a head restraint. The centre rear head restraint is designed solely for use with the centre rear seat. This head r ...

Hitching and connecting the trailer
First read and observe the introductory information and safety warnings Emergency breakaway cable Always fasten the trailer's emergency breakaway cable properly to the towing vehicle. Leave enough slack in the emergency breakaway cable so that the vehicle can still drive around corners. How ...

Legal Requirements
The manufacturer is granted general type approval for the whole vehicle including all parts and for specific retrofitting (general type approval according to § 20 StVZO (Motor Vehicle Construction and Use Regulations or EU type approval). ...